Knowledge Base:  

Page of 3
Auto Step and Limit Memory Scanning

The Limit Memory channels that are PMS scanning setup in the FTM-400 offer a Step option. This option is used by the radio during scanning only if Auto Step is turned off. The default for Auto St
2.5kHz steps in Wouxum KG-UV920P

The Wouxum KG-UV920P was first released without 2.5kHz steps. This would keep it from reaching a frequency such as 449.9775. You would receive an Invalid frequency error message when trying to enter t
PMS Steps
This is what I found with the FTM-400 and PMS scanning. Using programmer version 5.00.47, I set frequencies in the Band A and Band B Limit Memories. I also set Step to 5, 25, 12.5, 50, 100, and Aut
Communications Error - IC-7000
When the Communications | Get data from radio or Communications | Send data to radio process cannot communicate with the radio, the following message will be displayed. This message

Installing the software to a machine without a CD drive.


Asked often in reference to the new Netbooks and other "mini" computers. This process is completed easily by mapping a shared network CD drive to a letter designation on the receiving machine. On
Repeater Access Tones
With so many more repeaters today on frequencies so close together, repeaters are controlled with sub-audible tones to limit access and reduce interference. The tone frequency or DCS code assigned
Name/Frequency display
While operating on a memory channel with a name display, pressing the main tuning knob (on left) will display the frequency for the channel. Press the knob again to return to the name display. BE
The Option to not transmit
Some radios available today have the option that allows you to prevent or inhibit transmit on a given channel. Included here are those models and the steps to prevent or inhibit transmission (to Not
FM Narrow
As the airways become increasingly busy, requirements for narrow band operations have been implemented for many activities. These requirements involve output deviation and frequency step of the radio

IC-2100 Narrow Band Operations


Only the European version of the IC-2100 has FM Narrow capabilities as stated on page 58 of the Instruction Manual for the radio. This can be verified in a US version radio by stepping through th
Installation of the Programmer on Windows 8, Windows 8.1 and Windows 10
On some machines running Windows 8, 8.1 and Windows 10, installation of the RT Systems Programmers will display an error warning of Windows version compatibility. This seems to happen on machin
Narrow/Wide Band...it's all relative

There are two parts to this... frequencies and modulation. Frequencies : The new commercial frequencies and those assigned to Mars/Caps operations are on 2.5 kHz steps. i.e., 147.2125, 154
Install Disc 1 - error message at installation

The error message - " Install disc 1 " - occasionally happens when the program is installed. Most of the time, this means that it just had a problem with the drivers. The steps below will fix the pro
Memory Banks

To access the memory banks in the IC-2300 once they are programmed:  Press M-Call to access memory mode (at this point all your memory channels will be available when you turn the tuning k
Groups

Page 18 of the manual details Memory Channel Groups. Let me summarize here. The groups are predefined for the memory channels as shown in the first chart. Channels 0-49 are in Group 0, Channels 50-99
Cable Requirements

Step 1 - Install the software... Step 2 - Now attach A/B cable to radio/Power up radio - driver square should pop up - this will need some time to load everything - be patient & let it run.
Error During Update - updatelog.txt

During updates, or immediately following program installation, you may get an error that reads: "An error must have occurred Please send the file that is shown in the next screen to techsupport@rtsyst
Programming the FTM-400 via the SD Card
FTM-400 Data Transfer The ADMS-M400 Radio Programmer for the Yaesu FTM-400 Getting the initial details from the radio.
Send Data to Radio Fails (European Models Only) IC-7100, IC-9100

This guide may apply in cases where the following are true: You can get data from the radio (click Communications > Get data from radio) with no problems You cannot send data to the radio
Basic Settings Descriptions

This is a list and description of some of the more important settings in the RT Systems programmer. Please note that this is a general list – some radios may not have all of