Knowledge Base:  

Knowledge Base : Data transfer
Page of 1
Data Transfer

This is the only radio, we make software for that they may transfer partial loads of data, ex - could select just band A, or just band B, etc.
Data Transfer Issue

Data Transfer Issue   - Mic - must be MH-31 (basic 3 buttons and PTT) if it is anything else, it will interfere with the data transfer and must be unplugged.
Programmer to radio data transfer

Check these two settings in the radio TNC PKT - This will appear at the top left on the display of the radio.  This is turned off by pressing the [F] key for 1 second then the TNC key (bott
Can't do a data transfer - Version 3 (serial cable)

Using a black DB-9 serial cable?  Check the plug going into the radio - does it have 3 black rings and 4 silver (this is correct)?   Does it just have two black 
Can't do a data transfer - keypad locked?

Need to verify that the radio says CLONE   only , if the F8 above clone stays there - the keys are   locked -  it is in the manual (pg 16 - F/W key and the #6 for just the ke
Can't do a data transfer - keypad locked?

Using a black DB-9 serial cable?  Check the plug going into the radio - does it have 3 black rings and 4 silver (this is correct)?   Does it just have two black 
Programming the FTM-400 via the SD Card
FTM-400 Data Transfer The ADMS-M400 Radio Programmer for the Yaesu FTM-400 Getting the initial details from the radio.
Getting Started with the ADMS-FT1D Programmer
FT-1D Data Transfer The ADMS-FT1D Radio Programmer for the Yaesu FT-1D radio Programming the Yaesu FT-1D radio begins with gett

FT-991 Menu option that affects ability to transfer data between radio and Mac computer

Menu Item 33: CAT RTS can affect the transfer of data between the radio and the computer. Currently, we are seeing this issue on the Mac, however, this may be a solution for the ADMS-991/991A programm
VX-8 Differences (8D vs 8G)
Some differences between the VX-8D and the VX-8G There are more differences between the original VX-8D and the newer VX-8G that just the built in GPS unit. The receive frequency range of
Software and cable

The software for this radio was discontinued about 2004 and is no longer available.   (Even if they have a cable, we no longer have software. ) The baud  (data transfer) rate of the radi
Software and Cables

The blue USB-29A cable plugs into the outside speaker jack on the back of this radio. Page 9 in the owners manual will refer to this as #10 external speaker jack. (Cable is used for programming only)
FM Radio frequencies in the KG-UV6D
The FM radio station memories of this radio are not transferred by the radio with the memory channel data. They cannot be programmed from the computer. Once programmed into the special memories a
Quick Guide to Reading and Writing the FTM-400 Radio

Follow these exact steps from beginning to end to get data from or send data to the FTM-400 radio. You must get data from the radio before you can send data to the radio the first time. This gets bac
FTM-400 Checking Radio Firmware Version
FTM-400 Data Transfer The ADMS-M400 Radio Programmer for the Yaesu FTM-400 Using the SCU-20 cable   Programming the Yaesu FTM-40
The new programmer interface to RFinder Worldwide Database
RFinder Worldwide Database RFinder Worldwide Database Interface to RT Systems Programmers   The RFinder (RepeaterFinder) Worldwide Repe
Some things about the IC-R8600 Receiver that might be helpful as you learn this new radio.
A USB-A to USB-B (RT-42) cable plugged into the USB port on the back of the radio (the one next to the remote jack NOT the I/Q Out port) or a USB-A to Mini-B (RT-41) plugged into the USB port a
Radio does "NOTHING" with Get data from

The lock of the radio is tied to the power button. If you press the power button again after turning on that radio and do not hold it long enough to turn the radio off... it will lock. If the radio i
CT-131 Mic adapter

The CT-131 Mic adapter will not work for programming. It is not wired correctly to transfer programming data.
Cannot Find Valid Baud Rate on IC-7300

The port on the back of the radio into which the USB-B end of a USB-A to USB-B cable connects is multi-functional. You will set the commands for that port one way if you are controlling the radio or