Knowledge Base:  
Knowledge Base > Kenwood
Choose a sub category:
TH-D7 TH-D72 TH-D74
TH-F6 TH-G71A TM-271/471
TM-D700 TM-D710 TM-G707
TM-V71A TS-2000 TS-440
TS-480 TS-940

Page of 3

Cannot get data from Kenwood TH-K2 radio

When the radio is connected to a PC in order to use a programming cable (RT Systems USB-K4Y) and programming software, you MUST configure the SP/MIC jack function prior to making a connection between

Cross Band repeat operations on TM-V71 and TM-D710/d710G radios

The Kenwood mobiles, TM-V71A and TM-D710/D710G (American versions only of each) have crossband repeat functionality. This functionality can be set up to work with two radios for simplex operations or

Cross Band repeat operations on TM-V71 and TM-D710/d710G radios

The Kenwood mobiles, TM-V71A and TM-D710/D710G (American versions only of each) have crossband repeat functionality. This functionality can be set up to work with two radios for simplex operations or

KRS-710 Installer

During installation of the KRS-710 programmer, you will be prompted with the following screen to select the program for the Original (D-710) or newer (D-710G) radio. Be sure to install the correct ve
AL Channel on Call Tab

AL channel is used for programming the Weather Alert channel. This option is only available in the TM-271 radio and not the TM-471.
Band A and Band B 2M/440Mhz Separation

All memory channels are a part of Band A AND Band B. There is not a Band A set of memories and a Band B set of memories. However, the radio can be made to hide selected bands making it appear th
Band A and Band B 2M/440Mhz Separation

All memory channels are a part of Band A AND Band B. There is not a Band A set of memories and a Band B set of memories. However, the radio can be made to hide selected bands making it appear th
Cannot read TM-D710 - Error

When communicating with the TM-D710 using the our software the PC Port Speed must be set to 9600 bps. To change the PC Port Speed go to menu item 519 and change it to 9600 bps. After changi
Communicating with the radio

To establish communications with the TS-480, you must have the RTS and the DTS both set to ON.
Communicating with the radio

To establish communications with the TS-480, you must have the RTS and the DTS both set to ON.
CTCSS Tones

Note: Kenwood radios use a system of 42 CTCSS tones. Other radios use as many as 50 tones. When you copy from another file there may be a problem if the CTCSS value from the original data does not eq
Equipment required for EchoLink

To use EchoLink on the TM-V71, you'll need two separate cables for this radio. 1. The USB-K5G cable 2. PG-5H Cable (from Kenwood) You'll need to have both of these cables plugged into th
Failure of TM-D700 to communicate with the computer for programming

The TM-D700 is by far the "crankiest" radio we work with to program. It will work one day and not work the next. It has to do with it's age and design. This radio was designed long before modern comp
Firmware Updates

Yes our cables will work for Kenwood firmware updates - but you must have the COM port set below 20 - then reboot the computer for it to take effect and work.
Firmware Updates

The USB-K5G can be used for firmware upgrades from Kenwood on this radio.
Firmware Updates

The USB-K5G can be used for firmware upgrades from Kenwood on this radio.
Groups

Page 18 of the manual details Memory Channel Groups. Let me summarize here. The groups are predefined for the memory channels as shown in the first chart. Channels 0-49 are in Group 0, Channels 50-99
Groups

Page 18 of the manual details Memory Channel Groups. Let me summarize here. The groups are predefined for the memory channels as shown in the first chart. Channels 0-49 are in Group 0, Channels 50-99
Groups

Groups for this radio are designated as follows: 0-99 are Group 1 100-199 = Group 2 200-299 = Group 3  and so on, So if you do not have 99 frequency's you want in group 1, you ca
Groups

Groups for this radio are designated as follows: 0-99 are Group 1 100-199 = Group 2 200-299 = Group 3  and so on, So if you do not have 99 frequency's you want in group 1, you ca