The ID-31 Programmer is designed to give you the ease and convenience of programming the memories and set menu options of your radio from your PC including settings for D-STAR operations. The D-STAR calculator built into the program gives you D-STAR information from all around the world to use. You can easily set up your D-STAR channels with just a few mouse clicks.
Memory Channels Include:
Other Menu Item Categories Include:
The Radio Programmer Is for so Much More than Just Memory Management.
The programming process begins by first installing the program then installing (and allowing) the drivers for the cable. Be sure to complete both of these steps.
Save your file as you work. This is a computer, after all, and you would hate to lose your work should the system fail. Actually, create and save as many files as you want or need. You could have one file for home, a different one for the vacation house, another for the trip to your son’s house, another for the yearly 3K run and picnic where you help direct traffic and want the radio to be programmed with only the frequencies for that event. Remember, radio programming is an overwrite process. Everything in the radio is replaced by everything in the file.
Limit MemoriesLimit Memories are used by the radio for Program Scan. Program the same details for Limit Memories as for regular memory channels.
DR Channels:The DR Channels are preprogrammed in the radio with D-STAR information for you to use for quick manual channel setup from the radio’s face. D-STAR channels do not need to be programmed here.
Call Channel:Home/Call channels are special memories accessed through one button recall on the radio. These channels are preprogrammed in the radio and while the frequency can be changed to another within the band, they cannot be left blank.
GPS Memory:Once stored in the radio during GPS operations, these channels are read from the radio with the other details.
Memories and D-STAR Columns:The ID-31 handles D-STAR and FM memories in Memories. It is here in the Programmer that the D-STAR specifics for each channel are found. The D-STAR columns become active once Operating Mode is set to DV.
D-STAR SettingsSet “My Callsign” to your FCC issued callsign.
The list of Your Callsigns is storage.
In the ID-31, these come programmed from the factory. You can make changes to the list.
The callsigns used during a transmission are programmed in the memory channel. This list is available to make a selection from; however, the callsign does not need to be entered here first.
Tx messages, name/location/equipment details, etc., scroll on the radio receiving your call. Be sure to turn on the Tx message with the checkbox.
D-STAR Calculator Advanced
Source and Destination:The D-STAR Calculator automatically sets up the Talk, Echo, Info and Unlink channels for your “Source” repeater. The “Source” is the repeater you access to begin your adventures. Just like with analog repeaters, you must be able to hit the “Source” repeater.
Talk - the CQ channel for talking with others.
Echo - a test function that repeats your transmission back to you. Good for letting you know that you are, or are not, hitting the repeater.
Info - The function that triggers a status response from the repeater (i.e. linked to “where”... not linked).
Unlink - Disconnects the current link of the repeater (where allowed). More widely used to disconnect a link you establish. Remember... if you link, it’s always polite to unlink (hang up the phone) when you’re done unless someone has joined you locally. Then you might leave it to them to unlink.
The calculator sets up the same channels for a DVAP hotspot. You enter your frequency only once.
Route/Link to Repeaters:Now that you identified your “Source”, let’s set up your Destination. In D-STAR you can Link to Repeaters or Route to Repeaters. To set up channels that link or route, use the drop down at the top of the first tree to select your function, then select your repeaters by checking a country, region, state, city or individual repeater. A counter below the list keeps track of how many you have selected.
Link to Reflectors:For even more fun, and a great way for a beginner to get started, Link to Reflectors. D-STAR reflectors are a special type of Internet connected gateway that rebroadcasts each signal to all the other linked nodes or repeaters. Remember... EVERYBODY is listening... but that’s what makes it fun. You have a whole world to talk to through your local repeater, “Source”, linked to a reflector. To set up a channel that links your repeater to a reflector, check the box for that reflector in the Link to Reflector tree.
Click Apply once to set up all these channels for the radio.
The Resulting File:The resulting channels are set up and ready to go.
Your callsign, Rpt 1 Callsign and Rpt 2 Callsign are set automatically... No wondering which suffix goes where, or if it is positioned correctly. That is all done for you.
Name can be edited here to better identify the station. Name is what you see on the radio. It is not part of the D-STAR commands for use of the system. It may be all you have to identify the function of a channel. (Notice the frequency is the same for ALL these channels although they each do something different on the D-STAR network.) Make the Name something you understand.
Note: Be sure to turn ON the name display for the radio to use what you enter in the name field.
To Use these Settings for D-STAR Fun:• Save and send the file to the radio.
• Listen on the talk channel.
• Be sure your call sign is registered on the system.
• Check repeater status on info channel.
• Check your connection to repeater on Echo channel.
• Link repeater to a connection of your choice.
• Talk on Talk channel.
D-STAR Calculator for DR Memories:D-STAR Calculator for DR Memories lists repeaters worldwide for you to update or customize the list in the radio. Easily customize this list for places you plan to travel or places you want to work using a DR memory as your RPT2 repeater.
All repeater nodes are listed. Those the radio can use to transmit will be set automatically for “Repeater Use”.
Latitude and Longitude are included where that info is available from the source and the repeater is marked for use.
Click a country, region, state, city or individual repeater.
Use starting channel to replace or carefully add to your list.
No searching for data, it’s all right in the RT Systems Programmer.
The D-STAR calculator is updated automatically with the program. Just “Check for Updates” periodically to be sure you have the latest list.
Radio Menu Settings
Radio Option Setting Screens
Use these screens to customize other set menu features of the radio. Check boxes toggle features on or off, drop down menus list all selections and blank boxes for personalized entry add to the ease of setting up your radio exactly like you want it.
The entries on the Settings screens are made for you to “Set and Forget”. Once settings are customized, you are prompted to save before exiting. The saved settings will be there every time you create a new frequency file.
Set up options for Digital Speech and Voice operations.
Configure GPS function settings.
Enter DTMF memory details and customize options for this function of the radio.
Click here to learn more about using Preferences to customize your radio programming experience.