Programming the Yaesu FTM-300 with a MicroSD card.

FT-2D Data Transfer via SD Card
The YPS-M300 Radio Programmer
for the Yaesu FTM-300
Getting the initial details from the radio.
Programming the Yaesu FTM-300 radio begins with getting data from the radio. This gives the YPS-M300 Programmer the details it needs to identify the radio (worldwide version, modification status, and other "behind the scenes" details). This information can be retrieved only from the radio. Memory channel details are not important in this process.

This may be your first experience working with the SD card and the data transfer process. These steps will help you through that process.
Step 1: With the radio off, insert the SD card into the slot on the side of the head of the radio.
  • There is only one way the card will fit.
  • Do NOT force it.
  • The slot is on the left side of the face of the radio.
  • Shown here is a picture of the head only. You do NOT need to remove the head from the radio for this process.... this is just the only picture available.
  • Working so you are looking at the front of the radio, the teeth of the card will be facing away from you (toward the back of the radio).
  • The gold "teeth" go into the radio first.
  • Gently press the card into the slot until it clicks and stays firmly in place.

Step 2: With the radio on, press hold for 1 second the [F/SETUP] key on the face of the radio to access the Setup menu.

Note: In many of these instructions the [DIAL] at the upper right of the face of the radio is turned or pressed to control options that appear on the screen of the radio.
Step 3: Turn the [DIAL] to the the SD card option.Press [DIAL] to select the SD Card option.

Note: If the text of the SD Card option is not a red color, the SD card is either not seated properly in the radio or is not being recognized. Try removing and replacing the SD card or try another card.

Step 4: The SD Card options open with BACKUP highlighted. Press [DIAL] to select the BACKUP option.

Note: Backup is the option you want for this process. It is not necessary to format the card.

Step 5: Write to SD will be highlighted.
Press the [DIAL] to select this option.

This will transfer all the details of your radio to the SD card. Even in a new radio there are details that the Programmer uses to "sync" to this particular radio.

Step 6: All will be highlighted.
Press the [DIAL] to select this option.

You need ALL the details of the radio for the programming process. Everything about your radio is programmed... not just the memory channels.

Step 7: Rotate the [DIAL] to highlight OK.
Press [DIAL] to begin the process.




The details of the radio will be transferred to the SD card.

The process takes only a matter of seconds to complete.

The radio displays [Writing] while it is working.

[COMPLETED] appears on the face of the radio when the process finishes (if you miss the Completed message, the radio returns to the Write to SD card screen... if you're not press the [DIAL] again, then OK and watch through the entire process to be sure)

Step 8: Press Back button on the face of the radio to exit the Setup Menu. Remove the SD card and mount it in your computer.

It may not seem normal; but you press the SD card to release it from the slot. The card will "eject" and be ready to remove.

At all times be sure you do NOT touch to gold contacts. This could damage the card to the point it cannot be used by the radio or the computer.



Step 9: Start the YPS-M300Programmer

The program opens in a default file (FTM-300 Untitled).

If you have been working in the Programmer, it will open the last file you saved with memory channel details. To prevent loss of the memory channel information in this file, do File | New before proceeding to the next step. This will create a new FMT-300 file that you can work in.

Do Communications | Get data from SD Card from the options in the menu.

Step 10: Click OK on the message that lets you know the program has found the SD card.

This happens automatically as long as the SD card is recognized in the computer.

If a Windows File Open box appears, you either did not do the Backup in the radio or the SDcard is not being seen by the computer.

Step 11: If your radio is not yet programmed with any memory channels, it will appear that nothing happens in this step. The main screen does not change since there were no memory channels to display; but, the Programmer has retrieved the information it needs to identify your radio.

You have completed this part of the process and are ready to set up a file for your radio with memory channels, VFOs, Limit memories and customized menu settings.

You will need to repeat this part of the process you make changes on your radio that you want to save to the computer, if you modify your radio to transmit outside the ham band or if you do a firmware upgrade to the radio.


Step 12: Save your call sign permanently in the programmer.

Select Settings | Radio Menu Settings from the top of the screen.

On the settings screen, enter your call sign in the Call sign field at the lower left.

Click File | Save As (on the Settings screen)

Enter Settings as the Filename and click Save.

The Programmer will return to the Settings screen.

Click File | Exit to close the Settings screen.
Customize your file with details you want in your radio. Enter memory channels details including frequencies, names, tones, etc in the spread sheets.

As you build your file for the FT-3D radio, you will want to save it as you work.

Click File | Save As to save the file for use on the computer.

This is a part of the file that you will use to program the radio.

Step 13: Customize the file for your use.
Enter memory channels, Limit Memories, Home for A and B and VFOs as needed for your activities.

Use File | External data to access a data source from the Internet for repeaters in your area.

Save the file while you work. Use File | Save to make the file permanent on the computer. (This is not the file that programs the radio. This file is for you. You'll create a special file that the radio can understand.)
When you are ready to try your changes on the radio, click Communications | Write Data to SD Card to make the file ready for use by the radio.

This process will create the file that you will use to program the radio.

Step 14:

The programmer lets you know the process is complete


Step 15:

Remove the SD Card from the computer and put it in the radio.

Load it into the slot on the radio just as you did in Step 1.

Step 16:

Complete the process in the radio for Backup. (Steps 2-7) However, in Step 5 select Read from SD to transfer details from the SD card to the radio.

When this process is complete, the radio will be programmed like the file on the computer.

Remember: You may have to put the radio into memory mode with the V/M key to see the memory channels you loaded.